SINEAX i552 Single Phase Measuring Transducer

The SINEAX i552 Single Phase Measuring Transducers is an AC current transducer for effective value measurement. The SINEAX i552 Single Phase Measuring Transducer is a measuring transducer for the transformation of sinusoidal or distorted alternating current, with power supply terminal.

SINEAX i552 Single Phase Measuring Transducer features

  • Measurement method: Logarithmic process
  • Measurement input: alternating current, sinusoidal or distorted, true RMS value measurement
  • Measuring range: 1/5 A or 1.2/6 A selectable at terminals
  • Measurement output: unipolar and live-zero
    0…1.0 to 0…20 mA resp. live-zero 0.2…1 to 4…20 mA or
    0…1 to 0…10 V resp. live-zero 0.2…1 to 2…10 V
  • Power supply: wide DC, AC power pack tolerance
  • Standard as marine version per Lloyd’s Register of Shipping
  • P13/70 housing for top-hat rail mounting
  • CSA certificate , German Lloyd approval

SINEAX i552 Single Phase Measuring Transducer data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX U553 Single Phase Measuring Transducer

The SINEAX U553 Single Phase Measuring Transducer is a measuring transducer for the transformation of sinusoidal or distorted alternating voltage. The SINEAX U553 Single Phase Measuring Transducer is supplied with power supply terminal.

SINEAX U553 Single Phase Measuring Transducer features

  • Measurement method: logarithmic process
  • Measurement input: alternating voltage, sinusoidal or distorted, true RMS value measurement
  • Nominal input voltage: 0…20 to 0…690 V
  • Measurement output: unipolar and live-zero
    0…1.0 to 0…20 mA resp. live-zero 0.2…1 to 4…20 mA or
    0…1 to 0…10 V resp. live-zero 0.2…1 to 2…10 V
  • Power supply: wide DC, AC power pack tolerance
  • Standard as marine version per Lloyd’s Register of Shipping
  • P13/70 housing for top-hat rail mounting
  • CSA certificate , German Lloyd approval

SINEAX U553 Single Phase Measuring Transducer data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX F534 Single Phase Measuring Transducer

The SINEAX F534 Single Phase Measuring Transducer is a measuring transducer for frequency. The SINEAX F534 Single Phase Measuring Transducer is used for the conversion of frequency into a direct current or voltage signal, which is proportional to the measured value.

SINEAX F534 Single Phase Measuring Transducer features

  • Measurement input for sinusoidal, square-wave or distorted nominal input voltage with dominant fundamental wave
  • Input voltage: 10 to 690 V
  • Measuring range limits 10 Hz to 1.5 kHz
  • Auxiliary power: 85 to 230 V AC/DC
  • Input frequency response time periods: 4
  • Measurement output available with unipolar, bipolar or live-zero output quantities
  • Measuring method: digital period of oscillation measurement
  • Power supply: integrated AC-DC power pack with large tolerance range for universal use
  • Standard GL (Germanischer Lloyd) / suitable for use on ocean-going vessels
  • SINEAX housing: P13/70 housing for top-hat rail mounting
    EURAX housing: plug-in module (7 standard width units) for 19″ rack
  • CSA certificate , German Lloyd approval

SINEAX F534 Single Phase Measuring Transducer data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX G536 Single Phase Measuring Transducer

The SINEAX G536 Single Phase Measuring Transducer is a measuring transducer for phase angle/power factor. The SINEAX G536 Single Phase Measuring Transducer is used for the measurement of phase angle or power factor in single-phase or 3-phase electrical systems with symmetrical load.

SINEAX G536 Single Phase Measuring Transducers features

  • Measurement input for sinusoidal, square-wave or distorted nominal input voltage with dominant fundamental wave
  • Input voltage: 10 to 690 V
  • Input current: 0.5 to 6 A
  • Nominal input frequency: 50 Hz
  • Output: cosp linear
  • Auxiliary power: 85 to 230 V AC/DC
  • Input frequency response time periods: 4
  • Measuring range (for import): 0.5.. cap.. 1 .. ind .. 0.5 cosp linear
  • Measuring range limits: min. span 20 °el, max. span 360 °el
  • Measurement output available with unipolar, bipolar or live-zero output quantities
  • Measuring method: acquires distance between zero-crossings
  • Power supply: integrated AC-DC power pack with large tolerance range for universal use
  • Standard GL (Germanischer Lloyd) / suitable for use on ocean-going vessels
  • SINEAX Housing: P13/70 housing for top-hat rail mounting
    EURAX Housing: plug-in module (7 standard width units) for 19″ rack
  • CSA certificate , German Lloyd approval

SINEAX F534 Single Phase Measuring Transducer data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX P530 3-Phase Measuring Transducer

The SINEAX P530 3-Phase Measuring Transducer is a measuring transducer for active power. SINEAX P530 3-Phase Measuring Transducer is used for the conversion of active power in single phase alternating current or 3-phase systems with balanced or unbalanced load. A load-independent direct current or direct voltage is used as an output signal, which is proportional to the measured active power value.

SINEAX P530 3-Phase Measuring Transducer features

  • Measuring method: TDM method
  • Measurement inputs: sinusoidal nominal input current (1 or 5 A) and nominal input voltage (100 to 690 V)
  • Nominal input frequency: 50 Hz
  • Measuring range: 0 to 4 kW
  • Measurement output: unipolar, bipolar or live-zero output quantities
  • Power supply: integrated AC-DC power pack with large tolerance range for universal use
  • Standard GL (Germanischer Lloyd) / suitable for use on ocean-going vessels
  • Housings – top-hat rail mounting
    P13/70 housing for single-phase alternating current
    P18/105 housing for 3-phase current
  • CSA certificate , German Lloyd approval

SINEAX P530 3-Phase Measuring Transducers data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX Q531 3-Phase Transducer

The SINEAX Q531 3-Phase Transducer is a measuring transducer for reactive power. The SINEAX Q531 3-Phase Transducer is used for the conversion of reactive power in single phase alternating current or 3-phase systems with balanced or unbalanced load. A load-independent direct current or direct voltage is used as an output signal, which is proportional to the measured reactive power value.

SINEAX Q531 3-Phase Transducer features

  • Measuring method: TDM method
  • Measurement inputs: sinusoidal nominal input current (1 or 5 A) and nominal input voltage (100 to 690 V)
  • Nominal input frequency: 50 Hz
  • Measuring range: 0 to 2 kVar
  • Measurement output: unipolar, bipolar or live-zero output quantities
  • Power supply: integrated AC-DC power pack with large tolerance range for universal use
  • Standard GL (Germanischer Lloyd) / suitable for use on ocean-going vessels
  • Housings – top-hat rail mounting
  • P13/70 housing for phase-phase alternating current
  • P18/105 housing for 3-phase current
  • CSA certificate , German Lloyd approval

SINEAX Q531 3-Phase Transducer data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX M563 3-Phase Transducers (Programmable)

The SINEAX M563 3-Phase Transducer is a programmable multi-funtion transducer with 3 analog out and RS232. The SINEAX M563 3-Phase Transducer is used for simultaneously acquiring 3 freely selectable measured quantities in electrical systems. The SINEAX M563 3-Phase Transducer is equipped with 3 electrically isolated current outputs.

SINEAX M563 3-Phase Transducer features

  • 3 analogue outputs
  • Application (system) programmable
  • Rated current 1 to 6 A programmable
  • Rated voltage 57 to 400 V (phase-to-neutral) or
  • 100 to 693 V (phase to phase) programmable
  • Universal analogue outputs (programmable)
  • High accuracy: class 0.5
  • Software with password protection for programming, data analysis, power system status simulation, acquisition of meter data and making settings
  • DC, AC power pack with very large tolerance range
  • Mounting: For snapping onto top-hat rail
  • CSA certificate

SINEAX M563 3-Phase Transducers (Programmable) data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX DME 424 3-Phase Transducer (Programmable)

The SINEAX DME 424 3-Phase Transducer is a programmable multi-transducer for simultaneously acquiring several quantities in heavy current systems. The SINEAX DME 424 3-Phase Transducer‘s output quantities of the analog outputs can be configured as load-independent direct current or direct voltage signals. The digital outputs are suitable for limit value monitoring or energy metering.

SINEAX DME 424 3-Phase Transducer features

  • With 2 analog and 4 digital outputs
  • 4 programmable energy meters for Ah, kVAh, kWh and kvarh
  • Programmable application (type of electrical system)
  • Current to 10 A, voltage to 830 V
  • Programmable universal analog outputs
  • Accuracy: U/I 0.2%, P 0.25% under reference conditions
  • Universal digital outputs: meter transmitter, limit values
  • Password protected software for programming, data analysis and simulation
  • AC-DC power pack with large tolerance range, or AC only
  • CSA certification
  • SINEAX housing: top-hat rail or wall mounting
    EURAX housing: plug-in module for 19″ rack

SINEAX DME 424 3-Phase Transducers (Programmable) data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX DME 442 3-Phase Transducer (Programmable)

The SINEAX DME 442 3-Phase Transducer is a programmable multifunction transducer with 2 energy meters, 4 analog and 2 digital out with RS232. The SINEAX DME 442 3-Phase Transducer is used for simultaneously acquiring several quantities in heavy current systems. The output quantities of the analog outputs can be configured as load-independent direct current or direct voltage signals. The digital outputs are suitable for limit value monitoring or energy metering.

SINEAX DME 442 Transducer features:

  • With 4 analog and 2 digital outputs
  • 2 programmable energy meters for Ah, kVAh, kWh and kvarh
  • Programmable application (type of electrical system)
  • Current to 10 A, voltage to 830 V
  • Programmable universal analog outputs
  • Accuracy: U/I 0.2%, P 0.25% under reference conditions
  • Universal digital outputs: meter transmitter, limit values
  • Password protected software for programming, data analysis and simulation
  • AC-DC power pack with large tolerance range, or AC only
  • CSA certificate
  • SINEAX housing: top-hat rail or wall mounting
    EURAX houising: plug-in module for 19″ rack

SINEAX DME 442 3-Phase Transducers (Programmable) data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX DME 440 3-Phase Transducer (Programmable)

The SINEAX DME 440 3-Phase Transducer is a programmable multi-functional transducer with 4 energy meters, 4 analog out, RS232, RS485-MODBUS. The SINEAX DME 440 3-Phase Transducer is used to simultaneously acquire several quantities in heavy current systems and processes them into 4 analog output quantities. The MODBUS interface allows for querying up to 47 measured quantities.

SINEAX DME 440 3-Phase Transducer (Programmable) features

  • 4 analog outputs
  • 4 programmable energy meters for Ah, kVAh, kWh and kvarh
  • Programmable application (type of electrical system)
  • Current to 10 A, voltage to 830 V
  • Programmable universal analog outputs
  • Accuracy: U / I 0.2 %, P 0.25 % under reference conditions
  • Password protected software for programming, data analysis and simulation
  • AC-DC power pack with large tolerance range
  • CSA certificate
  • SINEAX housing: top-hat rail or wall mounting
    EURAX housing: plug-in module for 19″ rack

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX DME 400 3-Phase Transducer (Programmable)

The SINEAX DME 400 3-Phase Transducer is a programmable multi-function transducer with 4 energy meters, RS232, LON. The SINEAX DME 400 3-Phase Transducer is used for querying up to 47 measured quantities in heavy current systems. The SINEAX DME 400 3-Phase Transducer takes accurate measurement (class 0.2) of voltage and current, active, reactive and apparent power, power factor and frequency, as well as special current functions (bimetallic, slave pointer, mean value with or without preceding plus or minus sign).

SINEAX DME 400 3-Phase Transducer features

  • Current to 10 A, voltage to 830 V
  • 4 programmable energy meters for Ah, kVAh, kWh and kvarh
  • AC-DC power pack with large tolerance range, or AC only
  • User-friendly customer software
  • Top-hat rail or wall mounting
  • CSA certificate

SINEAX DME 400 3-Phase Transducers (Programmable) data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX DME 401 3-Phase Transducer (Programmable)

The SINEAX DME 401 3-Phase Transducer is a programmable multi-function transducer with 4 energy meters, RS232 and RS485-MODBUS. The SINEAX DME 401 3-Phase Transducer is used for querying up to 47 measured quantities in heavy current systems.

The SINEAX DME 401 3-Phase Transducer features

  • Data transfer via MODBUS interface
  • 4 programmable energy meters for Ah, kVAh, kWh and kvarh
  • Programmable application (type of electrical system)
  • Current to 10 A, voltage to 830 V
  • Accuracy: 0.2% (under reference conditions)
  • Password protected software for programming, data analysis and simulation
  • AC-DC power pack with large tolerance range
  • Top-hat rail or wall mounting
  • CSA certificate

SINEAX DME 401 3-Phase Transducers (Programmable) data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX DME 406 3-Phase Transducer (Programmable)

The SINEAX DME 406 3-Phase Transducer is a programmable multi-function transducer with 4 energy meters, RS232 and PROFIBUS. The SINEAX DME 406 3-Phase Transducer is used for querying up to 47 measured quantities in heavy current systems.

SINEAX DME 406 3-Phase Transducer features

  • Bus connection per EN 50 170
  • 4 programmable energy meters for Ah, kVAh, kWh and kvarh
  • Programmable application (type of electrical system)
  • Current to 10 A, voltage to 830 V
  • Password protected software for programming, data analysis and simulation
  • AC-DC power pack with large tolerance range, or AC only
  • Top-hat rail or wall mounting
  • CSA certificate

SINEAX DME 406 3-Phase Transducer data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX A210 Multifunction Power Measuring Instrument

The SINEAX A210 is a multifunctional power monitor and is used for the measurement and display of all values of a 3-phase current system. The SINEAX A210 Multifunction Power Measuring Instrument is of identical design to SINEAX A220, except for its dimensions, which are 96 x 96 mm.

SINEAX A210 is a multifunctional power monitor

  • Display of all 4 quadrants
  • 63 measurands with high accuracy (U, I: 0,5%)
  • 2 pulse or trip point outputs (S0)
  • Minimal installation depth: 46 mm
  • Transformer ratio programmable
  • 5 programmable intervals for active, reactive and apparent power (avg. values)
  • 8 energy counters for active and reactive energy. All counters show incoming and outgoing energy with 2 tariffs
  • Pluggable module with RS 232/RS 485 interface for MODBUS RTU
  • Pluggable module with RS 232/RS 485 interface for MODBUS RTU and data logger
  • After a power supply failure all values, counter contents, displayed values and programmed functions are available
  • The 14 mm high LED display ensures good readability
  • Dimensions: 96 x 96 x 46 mm

SINEAX A210 Multifunction Power Measuring Instrument data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX A220 Multifunction Power Measuring Instrument

The SINEAX A220 Multifunctional Power Monitor is used for the measurement and display of all values of a 3-phase current system. The SINEAX A220 Multifunction Power Measuring Instrument is of identical design to SINEAX A210, exept for dimensions, which are 144 x 144 mm.

SINEAX A220 Multifunction Power Measuring Instrument features

  • Display of all 4 quadrants
  • 63 measurands with high accuracy (U, I: 0,5%)
  • 2 pulse or trip point outputs (S0)
  • Minimal installation depth: 46 mm
  • Transformer ratio programmable
  • 5 programmable intervals for active, reactive and apparent power (avg. values)
  • 8 energy counters for active and reactive energy. All counters show incoming and outgoing energy with 2 tariffs
  • Pluggable module with RS 232/RS 485 interface for MODBUS RTU
  • Pluggable module with RS 232/RS 485 interface for MODBUS RTU and data logger
  • After a power supply failure all values, counter contents, displayed values and programmed functions are available
  • The 14 mm high LED display ensures good readability
  • Dimensions: 144 x 144 x 46 mm

SINEAX A220 Multifunction Power Measuring Instrument data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX A230 Multifunction Power Measuring Instrument

The SINEAX A230 Multifunctional Power Monitor is used for the measurement and display of all values of a 3-phase current system. SINEAX A230 Multifunction Power Measuring Instrument comes complete with with System Analysis. In addition to the features of the Sineax A210 and Sineax A220, this power monitoring device provides functions for system and load analysis. The system and load analysis is done by measurement of harmonics, THD, asymmetry, comprehensive average and max/min values.

The SINEAX A230 Multifunctional Power Monitoris of identical design to SINEAX A230s, exept for dimensions which are 144 x 144 x 46 mm. The SINEAX A230 is designed for application in high, medium and low voltage systems. Any current and voltage transformers are taken into account in the calculation of the measured values.

SINEAX A230 Multifunction Power Measuring Instrument features

  • Accurate measured values:
    U, I: 0.2% P, Q, S, PF, meter: 0.5% F: 0,02 Hz
  • 4-quadrant measurement of all values in AC systems
  • Clip-on extension module with average value and load profile recording, RS-232/485 interface, MODBUS, synchronizing input, switchover of high/low tariffs
  • Safe 3-way galvanic isolation between all circuits
  • 2 outputs for pulse or limit values
  • 4 meters for active power: Incoming/outgoing with high/low tariff*
  • 4 meters for reactive power:
  • Inductive/capacitive or incoming/outgoing with high/low tariff*
  • All counter values, recorded values, and settings are kept on a power supply failure
  • System/application: Single-phase 3L balanced/unbalanced (Aron, Full), 4L balanced/unbalanced (Open-Y, Full)
  • Dimensions 144 x 144 x 46 mm
  • 4-digit, 14 mm high LED display

SINEAX A230 Multifunction Power Measuring Instrument data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

EMMOD201 Multifunction Power Measuring Instrument

The Gossen Metrawatt EMMOD201 is an expansion module for SINEAX A210, SINEAX A220 and SINEAX A230 and enables programming and communication via RS 232 / 485 interface (switchable). The Gossen Metrawatt EMMOD201 features Modbus, Data Storage, RS 232 / 485 Interface and synchronizing input. The Gossen Metrawatt EMMOD201allows for the exchange of data with a control system via MODBUS RTU, and can be retrofitted without tampering with the basic device.

A200 software is required for programming the basic A2xx device and b with a PC, and for reading and selecting values from data storage.

EMMOD201 Multifunction Power Measuring Instrument features

  • Protocol: Modbus RTU for SCADA
  • Interface:R S232 / 485, switchable
  • Synchronizing input: synchronizing pulse for logger or for switching back and forth between peak and off-peak tariffs
  • Baud rate: 1200, 2400, 4800, 9600, 19.2 k
  • Data storage with A210 / A220
    Pint: mean active power value (import/export)
    Qint: mean reactive power value (inductive/capacitive)
  • Data storage with A230 / A230s
    Pint: mean active power value (import/export)
    Qint: mean reactive power value (import / export or inductive/capacitive)
    Sint: mean apparent power value and 9 additional, freely programmable mean values
  • Storage depth with 15 minute intervals:
    1 quantity = 166 days
    2 quantities = 83 days
    14 quantities = 12 days
  • Read + select values via A200 plus software

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

SINEAX A200 Multifunctional Display Unit

The Gossen Metrawatt SINEAX A200 is a multifucntional display unit for use with the SINEAX DME4 multi-transducers.The Gossen Metrawatt SINEAX A200 displays all measurands and meter contents of any DME4. The display unit is connected to the transducer via a simple RS232 interface cable, no more hot input wires at the cabinet door. By means of the direct connection to the transducer a first class accuracy of 0.15% (V, I) rsp. 0.2% (power and meter data) is guaranteed.

SINEAX A200 Multifunctional Display Unit features

  • Replaces numerous analog instruments
  • Displays all DME4 measurands locally, also for pure bus devices
  • Easy connection via RS232 cable
  • Dimensions 96 x 96 mm

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

Gossen Metrawatt U1389 Energy Meter (MID Approved)

The Gossen Metrawatt U1389 Energy Meter is an active Energy Meter with MID Approval. The Gossen Metrawatt U1389 is a calibrated energy meter and is used to acquire and bill active energy in industrial, household, commercial and building management applications. The Gossen Metrawatt U1389 Energy Meter is easy to install as the meter immediately indicates connection errors.

Relevant values are transmitted to data logging, billing and optimizing systems by means of a pulse output, or via LON, M-Bus or L-Bus interface. Depending on the type of multifunctional variant, the meter is also capable of acquiring reactive power and displaying up to 26 additional measured quantities.

Gossen Metrawatt U1389 Energy Meter features

  • Professional energy meters for 2, 3 and 4 wire systems with 65 A direct connection, or 1 A or 5 A transformer connection
  • Accuracy class B for industrial and commercial use, as well as for household use with highly demanding requirements
  • Cost savings thanks to initial calibration at the factory in accordance with MID, conformity assessment procedure modules B and D
  • Calibration even with adjustable transformation ratios
  • Configurable, multifunctional variants for acquiring reactive energy and mains quantities
  • Installation errors display: phase sequence, phase failure, transformers with reversed polarity, overload
  • Universal pulse output with adjustable pulse rate and pulse duration, as well as selectable voltage range
  • Flexible communication via integrated LON, M-Bus or L-Bus interface
  • Full functionality even when the electrical circuit is switched off thanks to failsafe 24 V auxiliary voltage
  • Tamper-proof cover, configuration disabling

Gossen Metrawatt U1389 Energy Meter data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

Dranetz Energy Platform/ Gossen Metrawatt MAVOWATT 20 3-Phase Energy & Power Analyzer

The MAVOWATT 20 3-Phase Energy & Power Analyzer is used to interpret utility costs, improve efficiency, install energy savings devices, explore alternative energy solutions or even determine your carbon footprint. The MAVOWATT 20 3-Phase Energy & Power Analyzer features a 1/4 VGA color touch display, automatic setups, easy to read reports and Energy Platform Report Writer (EPRW) software provide a simple to use, yet powerful tool for any application.

Gossen Metrawatt MAVOWATT 20 features

  • Advanced Demand, Energy, Harmonics and Power Analysis – Perfect for energy reduction/savings and alternative energy applications
  • Automatic setup – No learning curve!
  • Easy to read colorful Demand & Energy reports
  • Carbon Footprint Calculator – Evaluate environmental impact
  • Intuitive color touch screen
  • Available languages – English, Spanish, French, German, Italian, Swedish, Finnish, Chinese, Japanese, Korean
  • Eight Channels, 4 voltage & 4 current. Channel D Differential
  • AC and DC monitoring applications
  • High accuracy: 0.1% for voltage and current
  • High resolution: 256 samples / cycles – continuous monitoring
  • Triggered event detection on all parameters. Sag/Swell RMS detection, ±10% of nominal
  • Large memory up to 32 GB
  • AC or Battery operated. Built in UPS with 2hr battery.
  • Automatic Energy Audit reporting software – EPRW software included, no license.
  • DranView 6 software compatible – now has new Energy Audit report
  • Optional RS232, USB or LAN interface
  • Optional current measuring accessories

Gossen Metrawatt MAVOWATT 20 data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

Dranetz Energy Visa/ Gossen Metrawatt MAVOWATT 30 3-Phase Energy & Power Disturbance Analyzer

The Gossen Metrawatt MAVOWATT 30 3-Phase Energy & Power Disturbance Analyzer is a power and mains disturbance analyzer that fulfills the standards EN50160, EN61000-4-7 and EN61000-4-15 and EN61000-4-30. The Gossen Metrawatt MAVOWATT 30 is class A device that simultaneously monitors RMS values, harmonics, flicker and transients down to a time range of approximately 80 µs.

The Gossen Metrawatt MAVOWATT 30 has 8 measuring channels: 4 for voltage and 4 for current. The MAVOWATT 30 features intuitive  color touch-screen operation operated with the help of icons and multiple language options. All acquired data is saved to CompactFlash memory cards ≥4 GB and  Data communication is optional possible via RS 232, Ethernet or USB.

Gossen Metrawatt MAVOWATT 30 features

  • Power and mains disturbance analysis
  • Harmonic analysis per EN 61000-4-7
  • Mains quality per EN50160 with statistic bar chart
  • Flicker analysis per EN 61000-4-15
  • 8 measuring channels: 4 for voltage (differential) and 4 for current (current sensor), for measurements at 50 / 60 Hz power frequency
  • Data storage to Compact Flash memory cards ≥4 GB (scope of supply)
  • Power supply via charging device 90..264 V / 47..63 Hz
  • Built-in accumulator for up to 3 hour operating time
  • Optional RS232, USB or LAN interface
  • Optional current measuring accessories
  • High performance DranView PC analysis and evaluation software is available

Gossen Metrawatt MAVOWATT 30 data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

Dranetz Energy Guide/ Gossen Metrawatt MAVOWATT 40 3-Phase Energy & Power Disturbance Analyzer

The Gossen Metrawatt MAVOWATT 40 3-Phase Energy & Power Disturbance Analyzer is a power and mains disturbance analyzer that fulfills the standards EN50160, EN61000-4-7 and EN61000-4-15 and EN61000-4-30. The Gossen Metrawatt MAVOWATT 40 is class A device that simultaneously monitors RMS values, harmonics, flicker and transients down to a time range of approximately 80 µs.

The Gossen Metrawatt MAVOWATT 40 has 8 measuring channels: 4 for voltage and 4 for current. The MAVOWATT 40 features intuitive  color touch-screen operation operated with the help of icons and multiple language options. All acquired data is saved to CompactFlash memory cards ≥4 GB and  Data communication is optional possible via RS 232, Ethernet or USB.

The MAVOWATT 40 offers special modes for the recording of switch-on effects and fault note. Additionally there is an analysis module integrated for the direction of the voltage drop, switching tops of the power factor correction and the quality of motors.

Gossen Metrawatt MAVOWATT 30 features

  • Power and mains disturbance analysis
  • Harmonic analysis per EN 61000-4-7
  • Mains quality per EN50160 with statistic bar chart
  • Flicker analysis per EN 61000-4-15
  • Recording of switch-on effects and fault note
  • Integrated analysis module for the direction of the voltage drop, switching tops of the power factor correction and the quality of motors
  • 8 measuring channels: 4 for voltage (differential) and 4 for current (current sensor), for measurements at 50 / 60 Hz power frequency
  • Data storage to CompactFlash memory cards ≥4 GB (scope of supply)
  • Power supply via charging device 90..264 V / 47..63 Hz
  • Built-in accumulator for up to 3 hour operating time
  • Optional RS232, USB or LAN interface
  • Optional current measuring accessories
  • High performance DranView PC analysis and evaluation software is available

Gossen Metrawatt MAVOWATT 30 data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

Gossen Metrawatt MAVOWATT 50 3-Phase Energy & Power Disturbance Analyzer

The Gossen Metrowatt MAVOWATT 50 is an energy and power disturbance analyzer that measures electrical quantities in DC systems, as well as in single and three-phase AC systems with any load. The Gossen Metrowatt MAVOWATT 50 features eight isolated measuring circuits – four each for voltage and current. This prevents equalizing current and allowsfor simultaneous measurement of phase and neutral conductor voltage and current.

By connecting a suitable measuring transducer to the The Gossen Metrowatt MAVOWATT 50, the fourth channel can be used alternatively for the measurement of other physical quantities, e.g. the temperature of a motor or transformer, or wind speed at a wind power turbine.

The Metrowatt MAVOWATT 50 is suitable for stationary use and applications as well. The integrated rechargeable battery supplies power to the measuring instrument for periods of up to several minutes in the event of power failure.

Gossen Metrowatt MAVOWATT 50 features

  • Complete power disturbance analysis with simultaneous measurement of all relevant mains quantities
  • Power and energy analysis in power supply systems, as well as at the outputs of frequency converters
  • Harmonic analysis up to the 50th harmonic including sub-harmonics
  • Mains quality per EN50160 with statistical bar graph (Quick View)
  • Flicker analysis in accordance with EN 61000-4-15
  • 8 isolated measuring circuits (4 voltage and 4 current), 100 kHz sampling rate per measuring circuit
  • Color touch-screen display, 5½”, ¼ VGA
  • Storage of measurement data / settings to plug-in CF memory card or USB memory stick / hard disc
  • USB interfaces for external memory
  • Ethernet TCP/IP with integrated web server for remote control and read-out
  • 4 digital status inputs for indicating consumer operating states
  • 4 digital control inputs for synchronizing the measuring interval, and for use as meter inputs
  • 1 relay output for alarms
  • Power supply output for active current sensors
  • Integrated rechargeable battery with charging controller for power failures
  • Worldwide use is made possible with a broad range variable power pack (85 to 250 V AC/DC)
  • Functionally covered standards: EN 50160, EN 61000-4-7, /-4-15, /-4-30

Gossen Metrawatt MAVOWATT 50 data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

Dranetz PowerXplorer PX5/ Gossen Metrawatt MAVOWATT 70 3-Phase Energy & Power Disturbance Analyzer

The Gossen Metrawatt MAVOWATT 70 3-Phase Energy & Power Disturbance Analyzer is a power and mains disturbance analyzer. The Gossen Metrawatt MAVOWATT 70 fulfills the standards EN50160, EN61000-4-7 and EN61000-4-15, as well as EN61000-4-30. The Gossen Metrawatt MAVOWATT 70 is a class A device simultaneously monitors RMS values, harmonics, flicker and transients down to a time range of approximately 80 µs.

The Gossen Metrawatt MAVOWATT 70 has 8 measuring channels: 4 for voltage and 4 for current. The MAVOWATT 70 features intuitive  color touch-screen operation operated with the help of icons and multiple language options. All acquired data is saved to CompactFlash memory cards ≥4 GB and  Data communication is optional possible via RS 232, Ethernet or USB.

The Gossen Metrawatt MAVOWATT 70 offers special modes for the recording of switch-on effects and fault note. Additionally there is an analysis module integrated for the direction of the voltage drop, switching tops of the power factor correction and the quality of motors.

Gossen Metrawatt MAVOWATT 70 features

  • Power and mains disturbance analysis
  • Harmonic analysis per EN 61000-4-7
  • Mains quality per EN50160 with statistic bar chart
  • Flicker analysis per EN 61000-4-15
  • Recording of switch-on effects and fault note
  • Integrated analysis module for the direction of the voltage drop, switching tops of the power factor correction and the quality of motors
  • Extended functionality of the power analysis
  • Measurement of fast transients with 1 MHz sampling rate
  • 8 measuring channels: 4 for voltage (differential) and 4 for current (current sensor), for measurements at 50 / 60 Hz power frequency
  • Data storage to CompactFlash memory cards ≥4 GB (scope of supply)
  • Power supply via charging device 90..264 V / 47..63 Hz
  • Built-in accumulator for up to 3 hour operating time
  • Optional RS232, USB or LAN interface
  • Optional current measuring accessories
  • High performance DranView PC analysis and evaluation software is available
  • Special version for 50 / 60 Hz and 400 Hz mains frequency – MAVOWATT70-400

Gossen Metrawatt MAVOWATT 30 data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.

METRAHIT ENERGY Digital Multimeter

The Gossen Metrawatt METRAHIT ENERGY Digital Multimeter is a digital hand-held multimeter which takes a current and voltage measurement with a resolution of 60,000 counts.

Gossen Metrawatt METRAHIT ENERGY Digital Multimeter Features:

  • TRMS measurement including: V AC TRMS, V AC+DC TRMS with a bandwidth of 100 kHz, V DC, dB, Hz (V), Hz (A), Ω, μF, V Diodes, °C / F (TC / RTD)
  • Power measurement (W, VAr, VA, PF): active, reactive and apparent power with extreme values, power factor
  • Energy measurement (Wh, VArh, VAh), active, reactive and apparent energy, mean power value with adjustable observation period and maximum value
  • Mains quality analysis: recording of over and undervoltage, dips, swells, voltage peaks and transients in 0, 50 and 60 Hz systems
  • Harmonic analysis: RMS values and distortion components up to the 15th harmonic at 16.7, 50, 60 and 400 Hz
  • Crest factor CF, conductivity nS, low resistance RSL, duty cycle %, cable length km
  • Resolution of 60,000 counts
  • Triple display, display illumination can be activated under difficult lighting conditions
  • 1 kHz / -3 dB low-pass filter can be activated
  • Direct current measurement from 10 nA to 10 A, 16 A intermittently, current measurement with current transformer clamp and sensors, transformation ratio is taken into account at the display
  • Large data memory for up to 300,000 measured values
  • Instrument is completely remote controllable without activating the rotary switch or changing current sockets

Gossen Metrawatt METRAHIT ENERGY Digital Multimeter data sheet

Not exactly what you are looking for? Contact us with your exact requirements, we’re happy to help.